Mounting A Tub
Mounting A Tub
Blog Article
The content which follows involving A Step-by-Step Guide to Installing a Bathtub is pretty much attention-grabbing. You should investigate for yourself.
Installing a bath tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult job. If the old tub is easily accessible, the project can relocate quickly; if you need to open a wall to get rid of the old tub and also position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and fit trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one before you begin. Opportunities are you may need an expert plumber to make tube links.
This article will aid you mount a new tub in your washroom if you have actually already purchased a new bathtub and also don't need to alter the setup of your previous water pipes.
Your tools as well as product list should comprise the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be quite bothersome due to the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub up until the level reviews level.
To set up faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the regular outlet for leaks.
Ultimately, repair the bath paneling as defined in the manufacturer's user's manual. Tiling and also securing around the bath tub ought to wait till the bathtub has actually been used at the very least when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in place between the faucet and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our topic about How to Install a Bathtub. Thank you so much for finding the time to browse our piece. Are you aware of another person who is interested in the niche? Please feel free to promote it. I love reading our article about Installing A Bathtub.
This Page
Report this page